Flex C Ment Turkiye - Concrete Overlay Systems
Home Page
Quick Brick
Overlay Systems
Vertical Stamping
Flex-c-ment Stamps
Gallery
Training
Distributors & Installers
Color Chart
Color Recipes
Ready-Mix Concrete Stamps
Technical Information
Technical Tests
Sitemap
Contact Us
References
RSS Valid 2.0

AustriaPolish
 

Copyright 2013 Flex C Ment Turkiye.

MATERIAL SAFETY DATA SHEET

FLEX-C-MENT FLEX SEAL?
DBS Insaat Taahhut Kimya San. Ve Tic. Ltd. Sti
Bagdat Cad. No.198/1 Maltepe ? Istanbul / TURKEY
Date of Issue: May, 2004, FLEXSEAL

 

I . IDENTIFICATION OF THE SUBSTANCE/PREPERATION AND THE COMPANY
Flex-c-ment Flex Seal? ? Water Based Sealer

DBS Insaat Taahhut Kimya Sanayi ve Ticaret Limited Sirketi
Bagdat Caddesi No:198/1 Maltepe, Istanbul
Tel :+90 216 457 80 47
Fax: +90 216 457 80 46

 
II . COMPOSITION/ INFORMATION ON INGREDIENTS
No   Weight %
1 Water 70
2 Acrylic Polymer 22
3 Additives 8
 
III. HAZARD IDENTIFICATIONS
Particular information pertaining specific risk for human/environment
None known
 

IV. FIRST AID MEASURES
After skin contact
Wash away with soap and water and rinse. Do NOT use solvents or thinners!!
After eye contact
Flush with plenty of water(10-15 min)
After ingestion
Call a doctor

 

V. FIRE-FIGHTING MEASURES
Flash point??????????.Noncombustible
Auto-ignition Temperature ?..Not Applicable
Lower Explosive Limit????. Not Applicable
Upper Explosive Limit???.. ..Not Applicable

Material can splatter above 100C/212 F . Dried product can burn. Use extinguishing media (Carbon dioxide, foam,sand,water) for surrounding fire. Wear self-contained breathing apparatus (pressure-demand MSHA/NIOSH approved or equivalent) and full protective gear.

 

VI. ACCIDENTAL RELEASE MEASURES
Personal precautions:
No particular measures required

 
Enviromental precautions
No particular measures required
Methods for cleaning up/taking up
Wash off exhausted ink with cleaning cloths.Was away or put into house hold refuse.
 

VII. HANDLING AND STORAGE
Handling
Advise on safe handling
None
Advise on protection against fire and explosion
Material supports the burning only after evaporation of the watery content.
Storage
Keep from freezing; material may coagulate. The minimum recommended storage temperature for this material is 1 C/34 F. The maximum recommended storage temperature for this material is 60C/ 140 F.
Monomer vapors can be evolved when material is heated during processing operations. See Section 8 , Exposure Controls/Personal Protection, for types of ventilation required.

 

VIII. EXPOSURE CONTROLS/PERSONAL PROTECTION
Additional hints on technical system design
No particular measures required.
Ingredients with occupational exposure limits to be monitored
N O N E

 
IX . PHYSICAL AND CHEMICAL PROPERTIES
Form Viscous liquid
Colour Milky white
Odor Smell of ammonia
Initial boiling point Approximately 100 C Density Approximately 1.02 g/cm at 20 C Approximately 500 cps at 23C Viscosity Solubility in water Dilutable
Flash point N.A
Evaporation rate (BAC=1) <1
 

X . STABILITY AND REACTIVITY
This material is considered stable. However, avoid temperatures above 177 C /350
F, the onset of polymer decomposition. Thermal decomposition is dependent on time and temperature. Thermal decomposition may yield acrylic monomers. Product will not undergo polymerization. There are no known materials which are incompatible with this product.