Flex C Ment Turkiye - Concrete Overlay Systems
Home Page
Quick Brick
Overlay Systems
Vertical Stamping
Flex-c-ment Stamps
Gallery
Training
Distributors & Installers
Color Chart
Color Recipes
Ready-Mix Concrete Stamps
Technical Information
Technical Tests
Sitemap
Contact Us
References
RSS Valid 2.0

AustriaPolish
 

Copyright 2013 Flex C Ment Turkiye.

MATERIAL SAFETY DATA SHEET

Sentapol Synthetic and Natural Polymer Industry and Trading Co. Inc. Date of Issue: April , 2006, FLEXSEAL PROTECTOR

 

I . IDENTIFICATION OF THE SUBSTANCE/PREPERATION AND THE COMPANY
Flexseal PROTECTOR
Sentapol Synthetic and Natural Polymer Industry and Trading Co. Inc.
41700 KOCAELI
TEL: + 90 262 754 57 17
In case of emergency: + 90 262 754 57 21


II . COMPOSITION/ INFORMATION ON INGREDIENTS

No   Weight (%)
1 Water 72
2 Acrylic Polymer 23
3 Additives 5

III. HAZARD IDENTIFICATIONS
Particular information pertaining specific risk for human/environment
None known


IV. FIRST AID MEASURES After skin contact
Wash away with soap and water and rinse. Do NOT use solvents or thinners!!
After eye contact
Flush with plenty of water(10-15 min)
After ingestion
Call a doctor


V. FIRE-FIGHTING MEASURES
Flash point??????????.Noncombustible Auto-ignition Temperature ?..Not Applicable Lower Explosive Limit????. Not Applicable Upper Explosive Limit???.. ..Not Applicable
Material can splatter above 100C/212 F . Dried product can burn. Use extinguishing media (Carbon dioxide, foam,sand,water) for surrounding fire. Wear self-contained breathing apparatus (pressure-demand MSHA/NIOSH approved or equivalent) and full protective gear.

VI. ACCIDENTAL RELEASE MEASURES
Personal precautions:
No particular measures required
Enviromental precautions
No particular measures required
Methods for cleaning up/taking up
Wash off exhausted ink with cleaning cloths.Was away or put into house hold refuse.

VII. HANDLING AND STORAGE
Handling
Advise on safe handling
None
Advise on protection against fire and explosion
Material supports the burning only after evaporation of the watery content.
Storage
Keep from freezing; material may coagulate. The minimum recommended storage temperature for this material is 1 C/34 F. The maximum recommended storage temperature for this material is 60C/ 140 F.
Monomer vapors can be evolved when material is heated during processing operations. See Section 8 , Exposure Controls/Personal Protection, for types of ventilation required.


VIII. EXPOSURE CONTROLS/PERSONAL PROTECTION
Additional hints on technical system design
No particular measures required.
Ingredients with occupational exposure limits to be monitored

N O N E

IX . PHYSICAL AND CHEMICAL PROPERTIES

Form viscous liquid
Colour Milky white
Odor Smell of ammonia
Initial boiling point Approximately 100 C
Density Approximately 1.02 g/cm at 20 C
Viscosity Approximately 500 cps at 23C
Solubility in water Dilutable
Flash point N.A
Evaporation rate (BAC=1) <1

X. STABILITY AND REACTIVITY
This material is considered stable. However, avoid temperatures above 177 C /350
F, the onset of polymer decomposition. Thermal decomposition is dependent on time and temperature. Thermal decomposition may yield acrylic monomers. Product will not undergo polymerization. There are no known materials which are incompatible with this product.

XI. TOXICOLOGICAL INFORMATION
No toxicity data are available for this material.

XII. ECOLOGICAL INFORMATION
No Applicable Data

XIII. DISPOSAL CONSIDERATION

Procedure:
Coagulate the emulsion by the stepwise addition of ferric chloride and lime. Remove the clear supernatant and flush to a chemical sewer.

Special waste recommendations:
573 03 Dispersions or Emulsions of plastic material

XIV. TRANSPORT INFORMATION

Label Not Regulated
Land transport ADR/RID Non-dangerous goods
Marine transport IMDG/GGVSee The products does not constitute a hazardous substance in sea transport
Air transport ICAO/IATA The products does not constitute a hazardous substance in air transport

XV. REGULATORY INFORMATION
Labeling in accordance with directive 67/548/EEC (preparations) and 88/379/EEC, this product is not hazardous.

XVI.OTHER INFORMATIONS
According to their chemical structure, the applied raw materials do not contain any antomy, arsenic, soluble barium ,lead, cadmium ,chromium, mercury and selenium
Product conforms therefore to DIN EN 71,part 3
The instructions are based on today?s information and knowledge.The safety data sheet describes products in relation to safety requierements. These instructions do not assure application technological properties of the product.