I ? PRODUCT IDENTIFICATION
||TRADE NAME: Modifier 300
||Acrilic Modified |
|C.A.S. NUMBER ||Mixture ||HMIS
= 1 Fire = 0 Reactivity = 0 |
II - PHYSICAL DATA
>212 Deg. F
Vapor Density:41.0-45.0 by Weight
Heavier than Air. VOLATILE %
Specific Grav: 1.09
EVAP. RATE: Slower than n-Butyl Acetate.
liquid with no pronounced odor
III - FIRE AND EXPLOSION HAZARD DATA
CLASS: 3B Flash Point: >212 Deg. F LEL: N/A
-EXTINGUISHING MEDIA: Water, carbon dioxide, or dry chemical
-SPECIAL FIREFIGHTING PROCEDURES:
Firefighters and others
exposed to vapors or products of combusion should wear self-contained
-UNUSUAL FIRE & EXPLOSION
HAZARDS: None Known.
IV - HEALTH HAZARD DATA
The ACGIH TLV and OSHA PEL for vinyl acetate
are both set at 10 ppm for an 8-hour TWA and at 20 ppm for the STEL.
EFFECTS OF OVEREXPOSURE:
SKIN: This material may
cause skin irritation or rash upon prolonged or repeated contact.
INHALATION: Excessive exposure to vapors or spray mists can cause
irritation of eyes, nose and throat.
EYES: This material
may be an eye irritant.
SKIN: Wash with soap and water immediately.
EYES: Flush with
large quantities of water for 15 minutes and seek medical attention.
INGESTION: If ingested call a physician at once.
PRIMARY ROUTE (S) OF ENTRY: Inhalation of vapors (especially if strayed
inhalation study using laboratory animals exposed to high
concentrations of vinyl acetate for 6 hours per day, 5 days per week
two-year period has resulted in the development of
nasal tumors. Some of these tumors were shown to be carcinomas.
However, at this time, there is not sufficient evidence to indicate
that vinyl acetate may cause cancer in humans. There should be minimal
risk when used with ventilation adequate to maintain atmospheric
concentrations of vinyl acetate below the recommended exposure limit.
V - REACTIVITY DATA
|STABILITY: < >
Unstable <x> Stable |
< > May occur <x> Will not occur
-INCOMPATIBILITY: None known. -CONDITIONS TO AVOID: Keep from
-HAZARDOUS DECOMPOSITION PRODUCTS: Under
severe thermal degradation - low-molecular-weight organic compounds
will be formed.
VI - SPILL OR LEAK PROCEDURES
TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:
with water before allowing to dry. Sodium chloride can be sprinkled on
the spill, which may coagulate the latex and facilitate cleaning with
water. Place coagulated waste in a closed container. Wear protective
equipment during cleanup.
-WASTE DISPOSAL METHOD:
At this time, this material or its containers would not be considered
hazardous wastes as defined under the federal RCRA regulations (40 CFR
261) if discarded. Care should be taken to ensure that the material or
its containers are disposed of in an approved facility in accordance
with current federal, state, and local regulations.
For Further information, contact your state or local solid
waste agency or the United States Environmental Agency?s RCRA hotline
(800-424-9346 or 202-382-3000)
VII - SPECIAL PROTECTION INFORMATION
PROTECTION: Not generally required during normal use and handling. |
The need for respiratory protection should be evaluated if this
material is sprayed or heated in poorly ventilated areas.
-VENTILATION: General ventilation is recommended during normal use.
Local ventilation may be required during certain operations to prevent
inhalation of vapors.
-PROTECTIVE GLOVES: Chemical-resistant
nitrile, neoprene or rubber gloves required.
Wear face shield or chemical goggles.
EQUIPMENT: Wear protective clothing to prevent skin contact. Eye wash
station and safety shower should be available.
VIII - SPECIAL PRECAUTIONS
BE TAKEN IN HANDLING AND STORING: Avoid prolonged or repeated
inhalation of heated vapors or stray mists. Keep away from heat or open
flame. Avoid prolonged or repeated skin contact.
PRECAUTIONS: consult product bulletin prior to using this material.
IX - SUPPLEMENTAL INFORMATION
INFORMATION: None |
-SARA HAZARD CLASSIFICATION: This material
has been categorized as having the following hazards as defined by SARA
Title III regulations (40 CFR 370); acute, chronic.
SECTION 313 LISTED INGREDIENTS: The following ingredients in this
material are subject to the reporting requirements of section 313 of
SARA and 40 CFR
372 see Section II for percentage of
ingredients: Vinyl acetate monomer (108-0504)
SHIPPING NAME: Not regulated by DOT -UN NUMBER: None -DOT HAZARD CLASS:
is furnished without warranty, representation inducement or license of
any kind, except that is accurate to the best of Yoder & Sons
LLC knowledge, or obtained from sources believed by Yoder &
Sons LLC to be accurate, and does not assume any legal responsibility
for use or reliance upon same. |